SHOP BY APPLICATION    SHOP BY APPLICATION   
SHOP BY PRODUCT TYPE    SHOP BY PRODUCT TYPE   
SHOP BY COLOR    SHOP BY COLOR   
RESOURCES    RESOURCES   
REACH OUT    REACH OUT   
Your LayoutMap™ is Loading...Please Wait
Waveform Lighting's LED strips are assembled with wires and connectors on both ends of the reel. In some cases, however, you may end up needing to connect a shorter section of LED strip indepedently to a power source.

If that shorter section comes from the middle of the reel, you will no longer have the pre-attached wires or connectors available. This configuration chart demonstrates how solderless connectors can be used to connect wires onto the ends of cut LED strip sections so that it can be connected to a power supply unit.



← Back to all LayoutMaps™

image/svg+xml MODEL: YHY-2400500P/N:DS240120C14-WINPUT:AC100-240V~ 50-60hZ, 2.5AOUTPUT: 24V = 5.0A GNDWire to Ground FilmGrade™ DC Power Supply PART NUMBER 3092 STANDARD WALL-PLUG OUTLET AC 120/240V LINE VOLTAGE NEUTRALAC 120V/240V LINE VOLTAGE HOT/LIVEAC 120V/240V This power supply unit converts line voltage AC (100-240 volts) to low voltage DC output needed for LED strip operation. The unit plugs directly into any standard wall-plug outlet, and includes a male DC barrel jack connector on the DC output end.This product cannot be used with traditional wall-dimmers (e.g. Lutron / Leviton) but can be dimmed via an inline-dimmer connected on the DC output side. INPUT: AC 100-277 V + DIMMING OUTPUT: DC 24V The FilmGrade power supply includes a US-style two-prong plug that will fit in any standard wall-plug outlet. For use outside of North America, a voltage transformer is not needed, but a plug adpater may be necessary. Cable Length: 48 in (1200 mm) | NOT DRAWN TO SCALE INPUT: AC 100-240 V Cable Length: 48 in (1200 mm) | NOT DRAWN TO SCALE The PN 7094 Female DC Adapter is a convenient adapter that allows for a quick connection between a male DC barrel connector plug and a pair of positive and negative wires. Wires are secured in place via clamps that can be tightened by the pair of screws.In this setup configuration, PN 7094 is used to connect the output end of the power supply to the LED strip wires. PN 7094 Female DC Adapter PART NUMBER 7094 Standard DC Barrel Connector(5.5 x 2.1 mm) Standard NEMA 2-Prong Plug DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- CENTRIC HOME™/DAYLIGHT™ 95 CRI LED STRIP LIGHTS (24V)PART NUMBER 3004 This LED strip is configured as a 16.4 ft (5 meter) reel. It can be cut to shorter lengths as needed, in 2 inch (50 mm) increments using a pair of scissors.In this example, we assume that we are left with just the middle section of the reel, where we no longer have the pre-attached wires available. Simply slip the end of the LED strip into the plastic clip on the PN 3070 connector to connect the LED strip to the power feed. Cable Length: 7.9 in (200 mm) LED STRIP-TO-WIRE SOLDERLESS CONNECTORPART NUMBER 3070 PN 3070 includes a plastic connector on one end of a 6-inch cable, allowing you to quickly connect wires to the ends of LED strip sections in a matter of seconds without the hassle and mess of soldering.In this layout example, because our LED strip section no longer has the original pre-attached wires, we use PN 3070 to connect the LED strip end to the power source via the PN 7094 adapter. Cable Length: 5.9 in (150 mm) If last LED strip section is cut, the LED strip doesnot require any insulation or protection as the riskof a short circuit or electric shock across the copperpads is relatively low due to the low voltage DC design.