SHOP BY APPLICATION    SHOP BY APPLICATION   
SHOP BY PRODUCT TYPE    SHOP BY PRODUCT TYPE   
SHOP BY COLOR    SHOP BY COLOR   
RESOURCES    RESOURCES   
REACH OUT    REACH OUT   
Your LayoutMap™ is Loading...Please Wait
The following illustration shows the wiring and component configuration used to power four separate LED strip light sections from a standard wall-plug outlet. This is an ideal configuration for both residential and commercial installations where a "plug and play" solution is preferred, without the hassle of behind-the-wall rewiring and electrical work.

In this example layout, we connect Waveform Lighting's FilmGrade™ power supply unit to a full reel of CENTRIC HOME™/DAYLIGHT™ 95 CRI LED Strip Lights. Because the LED strip light does not have a corresponding DC barrel jack receptacle, we use the PN 7094 adapter to connect the power supply output to the LED strip wires.

This is a common setup for installations such as under-cabinet lighting applications where several short runs of LED strip may be interrupted by appliances or gaps such as stovetops or refrigerators. Note the max power supply capacity of 96 watts, which corresponds to approximately 16.4 ft (5 meters) of LED strip lights.



← Back to all LayoutMaps™

image/svg+xml MODEL: YHY-2400500P/N:DS240120C14-WINPUT:AC100-240V~ 50-60hZ, 2.5AOUTPUT: 24V = 5.0A GNDWire to Ground FilmGrade™ DC Power Supply PART NUMBER 3092 STANDARD WALL-PLUG OUTLET AC 120/240V LINE VOLTAGE NEUTRALAC 120V/240V LINE VOLTAGE HOT/LIVEAC 120V/240V This power supply unit converts line voltage AC (100-240 volts) to low voltage DC output needed for LED strip operation. The unit plugs directly into any standard wall-plug outlet, and includes a male DC barrel jack connector on the DC output end.This product cannot be used with traditional wall-dimmers (e.g. Lutron / Leviton) but can be dimmed via an inline-dimmer connected on the DC output side. INPUT: AC 100-277 V + DIMMING OUTPUT: DC 24V The FilmGrade power supply includes a US-style two-prong plug that will fit in any standard wall-plug outlet. For use outside of North America, a voltage transformer is not needed, but a plug adpater may be necessary. Cable Length: 48 in (1200 mm) | NOT DRAWN TO SCALE INPUT: AC 100-240 V Cable Length: 48 in (1200 mm) | NOT DRAWN TO SCALE The PN 7094 Female DC Adapter is a convenient adapter that allows for a quick connection between a male DC barrel connector plug and a pair of positive and negative wires. Wires are secured in place via clamps that can be tightened by the pair of screws.In this setup configuration, PN 7094 is used to connect the output end of the power supply to the LED strip wires. PN 7094 Female DC Adapter PART NUMBER 7094 Standard DC Barrel Connector(5.5 x 2.1 mm) Standard NEMA 2-Prong Plug DC 24V DC 24V +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- +- DC 24V DC 24V +- CENTRIC HOME™/DAYLIGHT™ 95 CRI LED STRIP LIGHTS (24V)PART NUMBER 3004 INPUT: DC 24V + DIMMING This LED strip has 16 AWG wires pre-mounted on both ends of the reel. The wire length is 13.8 inches (35 cm) and has tips stripped and tinned for quick and easy connection to power supply leads. This LED strip is configured as a 16.4 ft (5 meter) reel. It can be cut to shorter lengths as needed, in 2 inch (50 mm) increments using a pair of scissors.This configuration shows the entire reel cut into four sections of various lengths. The sections are then rejoined using solderless connector accesories and wires. Cable Length: 7.9 in (200 mm) LED STRIP-TO-STRIP SOLDERLESS CONNECTORPART NUMBER 3071 Solderless connectors are an indispensible accessory for configurations that require reconnecting LED strip sections that have been previously cut. PN 3071 includes plastic connectors on both ends of a 6-inch cable, allowing you to quickly rejoin LED strips in a matter of seconds without the hassle and mess of soldering.This part can also be used to make angled turns as the connector cable is both flexible and durable. Cable Length: 5.9 in (150 mm) LED STRIP-TO-WIRE SOLDERLESS CONNECTORPART NUMBER 3070 Similar to PN 3071, this part includes plastic connectors on just one end of a 6-inch cable, with open leads on the other end. This is a useful accessory item when connecting an LED strip section to another wired component.In this instance, we need to span a long distance to the next LED strip section, so we are using this connector to connect to a wire run (PN 7098). 16 AWG WirePART NUMBER 7098 Our 16 AWG wire is a heavy-duty wire rated for high amperage. Here, we are using it to span a long distance between LED strip sections so that we can connect them to the same power source.The product is sold in 33 ft spools (10 meters) and can be cut to length as needed. The ends should be stripped and connected to the wire ends of PN 3070 using twist-on wire connectors You may also use your own low voltage wire if prferred. Be aware that insufficient wire gauge can lead to voltage drop issues. Oftentimes "speaker wire" can be substituted for LED strip power feeds.PN 3070 can also be bypassed if you are comfortable soldering wires directly onto the LED strip copper pads. If leaving leads attached, we recommend terminatingor insulating wires to reduce short circuit risk DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- DC 24V DC 24V +- +- +- DC 24V +- +- +- DC 24V DC 24V +- +- +- DC 24V +- If last LED strip section is cut, the LED strip doesnot require any insulation or protection as the riskof a short circuit or electric shock across the copperpads is relatively low due to the low voltage DC design. Use Twist-On Wire Connectors("wire nuts") to Secure Use Twist-On Wire Connectors("wire nuts") to Secure